1. IMPORTANT:
    We launched a new online community and this space is now closed. This community will be available as a read-only resources until further notice.
    JOIN US HERE

DJM-T1 only plays in internal mode ....

Discussion in 'General DJ Forum' started by djtatt2, May 8, 2013.

  1. djtatt2

    djtatt2 Forum Member

    Messages:
    38
    The T1 will not switch to REL or ABS mode. Is this an update issue or not?

    Thanks in advance,
    TATT2
     
  2. DJ Freshfluke

    DJ Freshfluke Traktor Mod

    Messages:
    26,792
    more info... e.g. screenshots.
     
  3. Count Zero

    Count Zero ModerAUtor Moderator

    Messages:
    6,586
    It is an issue of the T1 is not scratch certified and so all scratch functions are disabled (assuming you even have traktor scratch in the first place.)
     
  4. koops

    koops New Member

    Messages:
    8
    EH? DJM-T1 is definitely scratch certified last time I checked!
     
  5. makar1

    makar1 Forum Member

    Messages:
    3,343
    The DJM T1 is a certified mixer, despite being missing from the list (along with the Z2). It also comes with Traktor Scratch so that shouldn't be an issue either, assuming that the correct software+serial have been installed.
     
  6. DJ Freshfluke

    DJ Freshfluke Traktor Mod

    Messages:
    26,792
    when i googled the hardware, it was said to be TSP certified. is it missing on the website list? i check and let NI know.
     
  7. djtatt2

    djtatt2 Forum Member

    Messages:
    38
    I can't send you a screenshot right now because i've unplugged the T1 and went back to Serato to prepare a VJ set i have to do Saturday.But i can tell you that, on the Traktor Screen both of the Rel. & Abs. buttons are grayed out and the Play button is not.
    ---
    Yes ....all of my Traktor and DJM T1 software/Serial have been installed correctly.
     
  8. makar1

    makar1 Forum Member

    Messages:
    3,343
    Do you get any timecode signal on the scopes?
     
  9. PiYo

    PiYo Forum Member

    Messages:
    65
    go to the T1 setting Utility and change the parameter from CD to Phono.
     
  10. djtatt2

    djtatt2 Forum Member

    Messages:
    38
    Hi,

    I've done that all so, also my Audio 10 works fine in scratch mode. Its the T1 that giving me the hassle.. Plus i can play my vinyl with the T1 without a problem also. I havent tried using any CDJ's with it so i dont if i'll run into the same problem.
    ---
    No i do not, all i get is "waiting" on the scopes. And to make sure i waited for 20 mins and still nothing.
     
  11. DJ Freshfluke

    DJ Freshfluke Traktor Mod

    Messages:
    26,792
    hence screenshhots... also from the respective prefs (audio setup e.a.)
     
  12. makar1

    makar1 Forum Member

    Messages:
    3,343
    If you get no signal at all, something is wrong with your routing.

    Have you set the "Mixer Output" settings correctly in the Utility Settings Window? (pg 12 of the manual). And are your hardware channels set to USB?
     
  13. djtatt2

    djtatt2 Forum Member

    Messages:
    38
    Ok then ...let me finish my other project and i'll setup the T1 again with the screenshots that you need to see.

    Thanks
    ---
    That's what i was thinking also and i followed the instructions on pg 12. But i'm going to put up the screenshots so i can help you guys better.

    Thanks
     
  14. dj_eddie_gr

    dj_eddie_gr Forum Member

    Messages:
    166
    If you have the T1 AND the AUDIO 10 ,then you should play in internal mode using A10 as a soundcard ,to hook the timecodes and get Master & HP out from. Remember to connect A10 directly to your PC/Laptop
     
  15. DJ Freshfluke

    DJ Freshfluke Traktor Mod

    Messages:
    26,792
    if he has a scratch certified mixer, he doesnt need to use the audio 10 at all...
     
  16. dj_eddie_gr

    dj_eddie_gr Forum Member

    Messages:
    166
    My bad. I thought that he was mentioning DDJ-T1 :p
     
  17. djtatt2

    djtatt2 Forum Member

    Messages:
    38

    Maybe i shouldnt have posted about the Audio 10 but i was laying out all the different paths that i have taken to the forum until i post the screenshots. My bad
     
  18. djtatt2

    djtatt2 Forum Member

    Messages:
    38
    I hope this helps ........

    Screen Shot 2013-05-18 at 9.34.13 PM.png

    Screen Shot 2013-05-18 at 9.34.37 PM.png

    Screen Shot 2013-05-18 at 9.34.46 PM.png

    Screen Shot 2013-05-18 at 9.35.07 PM.png

    Screen Shot 2013-05-18 at 9.36.06 PM.png
     
  19. makar1

    makar1 Forum Member

    Messages:
    3,343
    What settings are you using in the DJM-T1 Utility app, and are your mixer channel switches set to USB?

    Edit: A picture of your Audio MIDI Setup window might be helpful too.
     
  20. DJ Freshfluke

    DJ Freshfluke Traktor Mod

    Messages:
    26,792
    plus a pic of the scopes...

    without running record/cd, the provided screenshots look ok so far.