Help! Problems with Numark Omni Control & Traktor 3 LE

..........

6the monitor is on left mono 1 out 0 numark usb audio then
mono right 2 out 1 numark audio
then the rest says not connected, my driver is also one asio so im not sure what is wrong. is that tks file a new midi map thing and will it wrk for traktor 3. sorry if i sound dumb (i just wanna mix) and thanks for helping

 

Yes, it is the proper tks file and it should also setup your audio interface the way it is intended to work.
If it doesnt work try to swap the channels for monitor/cue and master

 

OK, I was having the same problems as you all have been having (i am running on a macbook pro have snow leopard...) and I found this document that helped me fix it. I hope it helps you... i also had to mess around with settings in Traktor LE but I finally got it all working flawlessly...

http://www.numark.com/stuff/content...e/traktor_le_and_mac_os_10.6_snow_leopard.pdf

 

i have a numark omni controller and traktor 3 and want to know if its possible to use it to control 4 decks at a tyme?

 

hi there iv got omni contoller and had problems first startin but it works fine now make sure u go trew the set up wizard and click the right contrller , drive's ?see if that helps im just startin my self tho. my laptop sed that the there was a corrupt file so couldnt insatll properly well a curupt file on the traktor le disk ? god noos but they helped me from there and i installed a curupt file free 1 from them . i was wounderin if any body could tell me if i could use a mpd24 with traktor pro and a omni contoller @ the same time or would i be able to use mpd24 with le and omni conteller at the same time plzz help im 21 and new to the seen but looove music plzz get back to me and maybe with a price for upgrade to pro

 

(did u find out if u could riun 4 decks with omni and traktor p)

 

How to use the file File Type: tks T34Midi Numark OmniControl.tks (22.2 KB, 171 views)

Who can help me set up it ?

 

I have everything working except for Par, fine pitch & tap. No LED or response.
I'm using Omni control, Macbook pro & traktor 3 LE.
I've tried changing device mapping to generic MIDI but it won't save. I've done all the reloading etc.
Can someone please help? Thanks

 

hi, sorry for going over old ground but have trid the suggestions on this forum but to no avail, i am running windows 7@64 bit, have a omni control, along with the supplied traktor LE, have downloaded the drivers from numark.com/tcdjexp. but still no joy! anyone out there can help me along, spoke to numak tech support they were of no help whatsoever.

 

Can someone tell me if Par & Tap work on the omni control with Traktor LE?

Just need to know if I need to upgrade Traktor or do I need to install again?

Thanks

 

This is the answer that I got from Numark Tech Support:

Hello

We are currently in final testing of drivers for Windows 7 64 bit. Please check www.numark.com as drivers will be posted as soon as they are available.

If you require any further assistance, please do not hesitate to e-mail me back.

Kind Regards

Dave Hill

We can only hope for a driver update but soon im sending my Omni back. I have tryed different installation procedures (incl those in this thread) but without any luck.

If some of you guys have news or any ideas please post!

Greets,,

Ranis

 

I followed Luishinos instructions (after having no luck whatsoever ) and was up and running after 10 mins.

Thanks.

 

dude is there any way u could send me your traktor 3 tsk file, i dont have my taktor le cd anymore to reinstall it and my omni works well on it so im gussing its not my omni thats not working just the teaktor 3.
please help