VCI-100 Map

Has anyone been able to get all the lights to work on the controler with this file?

 

lights

I can't comment on othe tsi's but you may want to check under 'interfaces' and check you have midi in and out checked. If these one of these is unchecked you don't get lights which are lit by midi commands. Also check the tsi and see if the author has put outputs to lights in the tsi.

 

Thanks. I'll make sure i have output selected just in case.

I started researching programing lights...

 

VCI-100 map by CyberMix from DigitalJockey team

Hi friends, this is the .tsi for Traktor 1.1.1 for two decks.
Next week I'll publish a similar .tsi that works with 4 decks.
I made it with first VCI-100 firmware so somebody can have problems of assignement in the effects section that you can resolve in few clicks.
The map is made to have the chained effects in panel 1 and advanced effects in panel 2.
I added here the image of shift (modifiers) map and the image with details of every commands.
The red, yellow and blue modifiers are made in toggle mode, so you have to push one more time to switch off the modifiers, the violet modifier is in hold mode.
I hope you glad.

 

Buggles' 2 deck VCI 1.2 for scratch pro

have a look!

basically designed with full fx flexibility and scratch control in mind. hitting relative mode will put you in timecode and play/stop will get you back in. I've omitted the balance in favor of input select for traditional wax or a mic. left for tsp and right for input.

some might rather change the tempo shift in this vci to a deck c+d modifier, or any other number of things. of course this button won't toggle the led so even with my current settings i'm tempted to make it a hold shift.
also, some might prefer beat jumps rather than next/prev cue. i might change it myself honestly.

I like to load decks from my laptop.

dry/wet doubles as the on button and in place of the effect on button i have an adv/chain toggle.

hope this gives someone what they were looking for,
peace.

 

How did you make those cool labels?

 

Plea to Finalcut

Hello Finalcut,

I have a very similar set up to yours and I could use some advice. My HD crashed on the MAC and I am in the process of starting over from scratch. The last time I configured the sound was over 2 years ago and now I can't seem to get it right.
I cannot remember how I set up the Output routing. I know it is stupid, but it is really frustrating to not be able to do one of the first steps.
I follow the instructions and it doesn't work.
The Main Output goes out 3 & 4 and the headphone mix is set to go out 1 & 2 (in Traktor's settings). However, I can hear the Monitor through the right speaker on top of the Main Mix, and just through the right headphone only, but not the left one.
The main mix is unbalanced too, but to the left - balance in the middle = half volume, to the left = full, to the right = nothing. I can't figure out if it has to do with the Mac's Audio/MIDI Set Up in Utilities or if it has to do with the Firebox Mixer or if I should change Traktor's Output routing.
It seems like it has mostly to do with the Mac's Audio/MIDI Set Up in Utilities. How do I configure the speakers on the MAC to match Traktor and Firebox so that the Main Mix is balanced and the monitor is only heard through my headphones?
How do you have yours set up?
Any advice would be much appreciated.

Thanks a lot,

Joe
joegatto16@yahoo.com

 

vci-100 scrolling function

Can you please send me the the file to be able to scroll thru music with the jog wheel. I'm on a mac.

Thank you.

 

Here's my latest vci-100 map for traktor scratch. Only few additions to the file i posted some pages earlier:
Use of a modifier for toggling fx instead of holding
Use of a modifier for browsing with the two jogs
Use of a modifier for browsing by pages (page up/down)
New documentation

 

I meant for Traktor Pro. I don't have scratch...

 

Does anyone have SILEK65 tsi file and jpeg pic to go with it? i know his tsi was vey similar to my layout.

any help would be appreciated@

 

My TSI for VCI-100 firmware 1.2 (Traktor Pro 1.1.1).
It´s for event (weddings, birthday) DJS that use little effects and loops.
It´s a basic NI map with a few modifications that help me in my work:

Set cue = store cue
4 little black buttons = cue 1,2,3,4
Deck effect button = effect on/off
Mid low = filter (3 eq)
No Xfader
1 effect (with all parameters) for each deck

Import all items to work well.

I´ll review this TSI and post some modification later.
Comments will be welcome.

PS: Sorry my bad english. I´m from Brazil.

 

I have his last one. Works great except when you push modifier and effect button it kills the bass on the track and turns on the effect for both decks...

 

news mapping tsi for vci vestax + keyboard

hello news tsi

 

don't have the vci anymore so can't comment. got a korg nano until someone brings out a decent controller.

 

Details on that the features/changes are?

 

sorry Greg75 i'm too late but i've bought my vestax right now i need to try good mapping with traktor pro. i'm reading your older posts and i would like to try platinum pl deluxe & gold tsi ?
Where can i find that?
Thanks so much man.

 

Tsi Mapping For Itm Dj Touch For Traktor Pro +vci 100 + Keyboard

TSI mapping itm dj touch for traktor pro + vci 100 vestax +* Keyboard

video itm dj touch /traktor pro
http://www.youtube.com/watch?v=ARRp0-7_fWI

 

Is this working with Windows OS?
thx greg75

 

it s ok