1. Please do not install macOS 10.15 Catalina yet, as Native Instruments software and hardware products are not supported under macOS 10.15 yet. For more info, please go HERE!
    Dismiss Notice

Xsession Pro with traktor... configuration midi problem

Discussion in 'TRAKTOR 3' started by FJDJ, Sep 13, 2007.

Thread Status:
Not open for further replies.
  1. FJDJ

    FJDJ NI Product Owner

    Messages:
    23
    Hello,

    Just bought Xsession pro and have a few little problems configuring it with traktor.

    1) when pitch bend assign to a buttom in Xsession pro, it stays press on traktor and rewinds or accelarates the track. I need it to, when press activates and when not press deactivate. Tried many different way to configured it and nothing....

    2) Some assign midi buttoms to for example "loop move" or "loop length bwd or fwd" have to be press twice to work.


    I like the Xsession pro, is small and confortable, so far is nice with traktor but this 2 little problems have get on my nerves.
    Without a pitch bend in the midi controller I still have to go the computer keyboards.

    If any one know how to fix this Ill be very grateful

    Thanks in advance
     
  2. FJDJ

    FJDJ NI Product Owner

    Messages:
    23
    Have anyone had this problem?

    Its not only with the Xsession Pro, but it also happens to me with an Xsession (the small without faders)......

    any suggestions?
     
  3. djk-tel

    djk-tel NI Product Owner

    Messages:
    328
    Search for my TKS file.

    Read up more on the MIDI assignments.
    You need to configure the MIDI assignment buttons within Traktor.
    It has nothing to do with the X-Session.

    Use my TKS for a reference.

    K-Tel
     
  4. FJDJ

    FJDJ NI Product Owner

    Messages:
    23
    I thinks i know what the problems is, if any know a solution ?


    I went to a friends house that has the same controller and when he presses Learn and then the "buttom" to assign in the controller, in assing in the midi page it appers "Note c# "

    When I do it with my controller it appears "CC82" as it was a knob or a fader.

    When i connect his controller to my laptob y appear "note C#" and it then works perfectly but with my controller it appears "CC88"


    How do I change it or what have to do so it appears "Note...." for assign bottoms and not "CC..."
     
  5. djk-tel

    djk-tel NI Product Owner

    Messages:
    328
    You may have to use Enigma to change what your X-Session output does.

    Or like I said. Find and refere to my tks file.
    check and see how it is set up and go from there.

    K-TEl
     
  6. FJDJ

    FJDJ NI Product Owner

    Messages:
    23
    whats enigma? and where are your tks files?

    thanks for your concerns
     
  7. FJDJ

    FJDJ NI Product Owner

    Messages:
    23
    ok, just got enigma from m - audio,

    lets see what I can do....
     
  8. djnuvoe

    djnuvoe NI Product Owner

    Messages:
    13
    Assign pitch nudge to midi button?

    Did anyone figure this out and post a how to?

    When I assign the pitch bend to a midi button it doesn't nudge it like the > in Traktor, it increases or decreases the pitch until I remove it.

    Tried numerous things and searches but haven't found the solution - anyone know? Is this going to be added to the user guide?

    Thanks in advance.
     
  9. djk-tel

    djk-tel NI Product Owner

    Messages:
    328
    Search and download my TKS file.
    Look at the MIDI pages and see what is happening.

    Did you assign it to pitch bend?

    K-Tel
     
Thread Status:
Not open for further replies.